Sr. Piping Engineer

  • Listed: July 17, 2018 1:30 pm
  • Job Type: Full Time
  • Salary Package: Negotiable
  • Required Experience: 5-10 Years
  • Minimum Education: Bachelors Degree
  • Emirates: Dubai
  • Country: United Arab Emirates
  • Employer Email:
  • Mobile: Rashid Malik +971 529060526


Dear Candidate,


We have been retained by one of our client to headhunt a professional for the position of Sr. Piping Engineer for Dubai.

The Jd is as follows :

Senior Piping Engineer (10 – 12 years)


Bachelor of Engineering (BE / B.TECH) in Mechanical from a reputed university with good academic record.


o Hands on experience in plant / package piping design and detail engineering is required.

o Working experience in Oil & Gas, Refinery or Petrochemical plant and skid package piping would be preferred.

o Shall have good amount of knowledge and exposure in pipe support design and stress analysis.

o Exposure to Aramco/ADCO/PDO/Shell/ONGC company specifications/Engineering practices related to piping and supports would be an added advantage.

o Exposure to international standards for piping, fittings, valves, etc., is essential.

o Knowledge in ASME, API, ASTM, EN codes and standards etc.

o Experience in selection of valves, datasheet preparation, evaluation of bids, engineering drawing review and approval of valve design is required.

o Experience in Piping Layout engineering.

Soft Skills

o Strong working experience in pipe stress analysis software CAESAR II

o Working Knowledge in Plant 3D software (CADWORX / PDMS or equiv)

o Familiarity with 2D software (AutoCAD / Microstation or equiv)

o Familiarity in MS-office

o Familiarity in SAP (Preffered)

Key Roles & Responsibilities (Responsibilities will include but not be limited to the following)

Roles & Responsibilities

o Reporting to Lead Engineer, must be capable of design and developing the Engineering deliverables related to piping ,Valves, Layouts, supports as per project requirement.

o Identify the scope of work & list of doc deliverables by going through the piping specifications and piping standards received as part of project requirement.

o Attending the internal Project Kick of meeting along with Lead Engineer and clarify the piping related issues or doubts or missing specifications if any to be obtained from client.

o Providing Inputs to Designer to prepare the preliminary layouts during pre-order and post order as per client requirement.

o Preparing/Reviewing and Approving of pipe sizing and hydraulic calculations. Checking the adequacy of pipe size recommended by the client.

o Providing inputs to Designer in preparing the project specific piping specifications.

o Preparing/Reviewing and Approving of preliminary piping BOM based on P&ID and PMS.

o Preparing/Reviewing and Approving of Plant / skid 3D modelling with respect to piping spec correctness & completeness, piping routing, insulation requirements if any, accessibility, supports & its locations, drain & venting requirements, etc.,

o Preparing/Reviewing and Approving piping stress Analysis using CAESAR II or equivalent software. Sometimes manual stress calculation and preparing the report.

o To Design the pipe supports based on stress calculation output. Assisting structural Engineer / Designer to prepare the support fabrication drawings.

o Reviewing and Approving of piping isometric drawings and support drawings.

o Reviewing and Approving of final piping BOM.

o Reviewing and Approving of As-built drawings.

o To Participate in Design review meetings (internal or external) as necessary.

o Issue of Purchase Requisitions, TDC’s, Datasheets as required for Piping and Piping Specialty Items, Valves etc.,

o Technical Bid Evaluations (TBE), and Vendor Recommendations

o Vendor Documents Review and approval

o Responsible for Coordination with other Disciplines in the Engg. Department in finalizing skid design including Interdisciplinary Check(IDC).

o Attending Shop floor and site issues if any

o SPDP or SPIR document compilation

o Provide assistance as required to Engineering Dept. for preparation of FAT, pre-commissioning and commissioning procedure as applicable

o Review of Interdepartmental procedures from technical point of view (Quality, Production etc.,)

o To identify the areas of concern with respect to progress of assigned work.

o Maintain the morale of the design team.

o Completing the given task in a specified time frame with at most care and professional manner.

o Lead by example; be prepared to perform all tasks required in the initiation, close and execution of the project.

o Knowledge in developing new packages (Preferred)

o Mentoring Engineers, Designers to the Project Requirement

Interested candidate can send their CV on alongwith scan copies of educational certificates and passport.

Rashid Malik

+971 529060526

Job Type: Full-time


Piping design and detailed engineering: 10 years


Share with Friends

Mention that you found this ad on when you Call or Message.

Listing ID: 885b4caecbdfc5c

Report problem

Processing your request, Please wait....